How much water: the settings
These settings decide how much water a routine watering gives and how it is split. Everything else (rain, soil, growth) adjusts from here.
How it fits together
ZoneFlow works with a weekly amount of water, in millimetres (1 mm on 1 m² is 1 litre; 25 mm is about 1 inch). Every few days it gives the share of that week that has come due:
watering = weekly target ÷ 7 × days between waterings − useful rain since the last watering
So with a weekly target of 28 mm and 4 days between waterings, one watering is 16 mm. Rain since the last watering is taken off. The flow rate turns the millimetres into minutes.
Emitter Flow Rate Calibration
How many millimetres of water your drippers or sprinklers put on the ground per minute. It is the one number every watering time is worked out from, so it must be measured, not guessed. A flow rate that is twice too high waters half as much as you think. Use the Calibrate the flow rate button on the zone card, or see Calibration.
Routine Normal, Hot and Cool Weekly Target
How much water the plant gets in a week of normal, hot or cool weather. The plant type you chose at setup filled these in. Starting points for a normal week (a hot week is about 1.3 times that, a cool week about 0.6 times):
- Lawn: 25-35 mm
- Vegetables, salad, flowers: 20-30 mm
- Herbs: about 15 mm
- Shrubs, young trees: 15-20 mm, plus the deep soak
- Fruit trees, established trees: 25-45 mm, plus the deep soak
- Succulents, drought-tolerant plants: 10-20 mm
In a hot or tropical climate lean to the high end, in a cool one to the low end. A thick mulch lowers what a plant needs. These are only starting points: watch the plant for two weeks and change the target by about 10 % at a time.
Routine Days Between Waterings, and (Hot)
How many days pass between routine waterings: one slider for normal and cool weather (4 days to start with), one for hot weather (3 days). From 1 to 10 days.
A longer gap does not mean less water. The weekly target stays the same, so each watering is bigger. Choose by root depth and soil:
- Shallow roots or sandy soil (salad, herbs, strawberries, seedlings, pots): 1 to 2 days. A shallow root zone holds little water, and sand drains fast.
- Most vegetables and flowers in loam: 2 to 4 days.
- Shrubs, trees, lawn on deep soil: 4 to 7 days. Bigger, less frequent waterings push the roots deeper.
If one watering becomes too big for the Routine Max Safety Runtime Cap, Check my setup says so.
Water Demand Model
How the weekly amount is chosen.
- Temperature tiers (the start): normal, hot or cool week, from the average of the last three days' highs. Simple, easy to understand, and hard to get badly wrong.
- ET curve: the water the weather takes out of the soil and plant, worked out from the daily lowest and highest temperature and your latitude (the Hargreaves method), times the crop factor. It follows the seasons and the length of the day smoothly. It needs a temperature sensor; without a reading it uses the tiers for that watering.
Which one to choose: ET, temperature tiers or a soil sensor.
Crop Factor (Kc)
Only used with the ET curve. How much water this plant uses compared with a short, well-watered lawn (the reference the weather calculation is made for). 1.0 means the same, 0.5 means half. The weekly amount is the daily ET × 7 × this factor. The Watering tips button on the zone card looks your plant up and can set it for you (see Watering tips).
Starting points for a full-grown plant in its main season, from the FAO crop tables and extension services:
- Tomatoes, peppers, squash, most vegetables at full size: 1.0-1.15
- Strawberries: 0.85-1.0
- Cool-season lawn: 0.8-0.95
- Warm-season lawn: 0.6-0.8
- Avocado: 0.75-0.85
- Citrus: 0.65-0.7
- Olive: 0.6-0.7
- Stone fruit in season: 0.9-1.0
- Succulents, drought-tolerant natives: 0.3-0.5
For a young plant keep the full-grown value and let the growth ramp give less while it grows. Do not lower the factor for mulch or bare soil: the Mulch setting does that, and doing both counts it twice.
The Hargreaves method uses temperature only. In very humid places it can read a little high, and in dry, windy places a little low. If the plant tells you otherwise, move the factor by 0.05 at a time.
Hot and Cool Weather Temp Threshold
Where a hot week and a cool week start. ZoneFlow takes the average of the last three days' highest temperatures. At or above Hot, the zone uses the hot target and the hot gap; below Cool, the cool target; in between, normal.
The climate you chose at setup filled these in:
- Tropical: hot at 31.5 °C, cool below 30 °C
- Hot, dry summers: hot at 34 °C, cool below 26 °C
- Temperate: hot at 28 °C, cool below 20 °C
- Cool summers: hot at 24 °C, cool below 16 °C
Change them only if your summers are unusual. Cool must stay below Hot.
Fallback / Manual Temperature
The temperature ZoneFlow uses when it has no real reading.
- A zone without a temperature sensor: this is how you tell it about the weather. Raise it above the hot threshold in a heat wave and below the cool threshold in a cold spell, then put it back.
- A zone with a sensor: used only after three days in a row without any reading. Leave it in the normal band.
Routine Pulse Count (Split-Cycle)
Into how many parts a watering is split, with a soak between them, so the water sinks in instead of running off. This is the least number of pulses: ZoneFlow adds pulses by itself when the soil, drainage or slope need them (up to 8). One pulse takes in about 3 mm on clay, 7 mm on clay loam, 15 mm on loam, 20 mm on sandy loam and 30 mm on sand, less on slow-draining soil. A moderate slope adds one pulse, a steep slope two.
Leave it at its starting value unless you see water pooling or running off. Then raise it by one.
Routine Soak Interval Between Pulses
How long the valve stays closed between pulses, so the water can soak in. Extension guidance (Texas A&M) is 30 to 60 minutes, at least an hour on clay. Sand needs little soak. 0 runs the pulses back to back.
The soak makes a watering take longer from start to finish, not more water.
Routine Minimum Pulse Length
The shortest a pulse may be (1 minute to start with). When a watering is too small for every pulse to reach this, it runs fewer pulses. Raise it if your drippers need a while to fill the pipe and reach full pressure (long lines, pressure-compensating drippers): 2 to 3 minutes.
How to tell if it is right
Look at the plant early in the morning. Drooping in the afternoon heat is normal for many plants; drooping that is still there in the morning means too dry. A day after a watering, push a finger or a trowel in where the roots are (5-10 cm for vegetables, 15-20 cm for trees): moist is right, dry means too little, soggy and cold means too much. Change one thing at a time and give it a week or two.